Smith Meter® AccuLoad and AccuLoad III are trademarks of FMC The default or operating values used in this manual and in the program of the AccuLoad III. AccuLoad III High Speed Prover Output · AccuLoad III Vapor Recovery Application Bulletin · AccuLoad IIInet Application Manual · AccuLoad III-S N4 Hardware. The default or operating values used in this manual and in the program of the Smith Table of Contents iii. Volume Accuracy – Preset Amount Type.
|Published (Last):||21 June 2015|
|PDF File Size:||6.3 Mb|
|ePub File Size:||17.14 Mb|
|Price:||Free* [*Free Regsitration Required]|
Each of these is delivered as a type of mini-batch, complete with individual high flow rates, first trip volumes, and so on. It is configurable to support a variety of user applications. Straight product, sequential blending, ratio blending, side-stream blending, hybrid blending and unloading.
Facilities described may or may not be supported More information.
Energy saving system in More information. The AccuLoad also has the capability of providing an average meter factor over a maximum of ten proves. Table does not include hybrid configuration.
404 page not found
To use the features described in this chapter, log in to the modem router. Arduino Wifi shield And reciever. Other significant features are as follows: One arm may be in Run mode while the other is in Ready mode, or both arms may be in Run or Ready mode simultaneously. Each time a transaction is ended and a new transaction is begun, the AccuLoad III will start a new prove with Step In the event that the meter factor is not successfully downloaded, the AccuLoad III will display a message indicating that the meter factor was rejected.
The remaining items are optional. This feature requires a load arm type to be programmed as Straight with VRS.
FMC Measurement Solutions – AccuLoad III Controllers Manuals
From the main menu, the unit may be moved into the dynamic displays, the print menu, program mode, or the diagnostics menu. Press up or down arrow to acccuload recipe. The following More information. Product delivery is controlled by several program code entries. The life of the battery used for the backup RAM can vary due to operational conditions, particularly the amount of.
Note zccuload the amount of information displayed is reduced in this mode, and that many abbreviations are required.
The F1 key selects the load arm to be actively displayed on the top viewport. The flow rate ramp-down from first trip to the end of the batch will be the same as if not proving. The zoom of the physical display is maintained as the focus changes.
Settings 4 5 Part IV Registering. Other possibilities are two three-product arms, or a four-product and a two-product arm, etc.
The hybrid blend consists of one sequentially blended product line feed by up to five main products combined with one to five product streams that are ratio blended into the main products. A contact is available to start and stop a ii or other electrically operated equipment as well as a program code that will set the lii delay of that start or stop. Instead, it will invoke a user prompt to select a specific arm to receive the focus.
Facilities described may or may not be supported. When the automated proving mode is activated, the AccuLoad will calculate the meter factor for a proving run based on information that is obtained during the prove. Page of 94 Go. Safety and volume accuracy functions including excess high flow, low flow, overrun, acuload temperature probe failure are also monitored per their program parameters.
Smith Meter AccuLoad III
This is most commonly done with products that mix very easily. This feature allows the operator to prove the meter on all four products, manuql four meter factors and associated flow rates acculoaad each product without having to enter the program mode for each product and meter factor. When the operator enters the preset, the AccuLoad automatically calculates the actual volumes of each product to be delivered. A remote collaboration consists in configuring, programming or monitoring a PLC from a remote location, without the need of.
If the message will not fit, it will be wrapped to the next line. Additive Monitoring Additive injector feedback provides the capability of the AccuLoad monitoring the additive zccuload that are being injected. The AccuLoad can also pass card data and status to a host computer. The DL Preset Controller. When using Firmware Revision and above, the AccuLoad supports temperature compensated flow additives, mass meter communications, and non-cyclic meter pulse averaging.
Integrated Control Technology More information. Pressing the zoom key F2 has no effect while the main msnual or any of its submenus is being displayed. To perform Ethernet setup and communication verification, first perform RS setup and communication verification: For example, Load Arm 1 must be programmed before Load Manuwl 2.
If the AccuLoad is in full screen mode, pressing F2 will shift from one full-screen load arm display to the other full-screen load arm display. This script will walk you through the basic process of setting up the remote access, data logging, FTP file More information. Implementing this feature requires that a load arm be identified as unloading ; up to six load arms can be so configured. After each problem description, instructions are provided. UL Listed and Classified. Bristol ControlWave Redundant Control October 19, – Page 1 Bristol ControlWave Redundant Control Redundant systems are offered for critical processes and harsh applications that require maximum operational readiness and system availability.
F2 will not affect the zoom when five or six load arms are programmed for use. When booting More information. Using the up and down arrow keys, select the kanual recipe. When the operator enters the preset, the AccuLoad III automatically calculates the actual volumes of each product mahual be delivered.