Shop for American DJ V Power Amplifier and more at everyday discount prices with free shipping over $50* on – Your Online Store!. Buy the ADJ V Amplifier at PlanetDJ. Low VIP Pricing, Financing and Free Shipping available. American Audio | V | User manual | American Audio V User manual American Audio® – – V Vplus Series Amplifiers Power.
|Published (Last):||14 June 2015|
|PDF File Size:||19.98 Mb|
|ePub File Size:||14.27 Mb|
|Price:||Free* [*Free Regsitration Required]|
Configuring the Low Amerocan Filter: Thermal Protection – Ametican single variable-speed fan on the V Vplus and dual variable speed fans on the V Vplus and V Vplus amplifiers provide adequate cooling. Insert the banana jacks into the caps of the binding post, be sure that the banana jack is inserted securely to avoid the risk of it popping out.
Never block the fan in any way or mount in an enclose rack, doing so may dh the amplifier to overheat and fail. After inserting the wire into the binding post hole, screw the binding post cap down on the wire.
This fans are used to cool the internal parts of the amplifier when in use. Cooling Fan – This is a dual speed cooling fan. Turn your input source level up. You may also visit jd on the web at www.
Insert the spade connector in to the binding post and tighten the caps down on the spade connector. In the event of an electrical overload the breaker will pop-out. To reset the breaker, push it in.
Always be sure the source voltage for your areas matches the required voltage for your amplifier. Channel 1 Gain Control – This rotary knob is used to control the output signal of channel one.
Low Cut Filter V and V Only – The low-cut filter removes extremely low frequencies from the audio signal that could cause speaker distortion or damage. During normal operation below clipping, and momentary clips on peaks, the limiter does not affect the audio signal and is inaudible.
Rear mounting the unit is especially recommended if the unit is to mounted into a mobile rack. Antes de usar este amplificador, lea mas advertencias en la guia de operacion. Turn channel two gain up. Amplifiers arrive to you preset in the stereo operation mode. This is to protect any speakers xmerican to the channel. When the channel aamerican into protect mode all output for that channel will turn off.
This may reduce the buzz that is caused from an electrical 60Hz cycle. Turn your amp on. Fuse Holder – This holder houses the external fuse. amerrican
Although a speaker will operate with the positive and negative leads plugged into either terminal on the amplifier binding post, be sure to plug the negative lead into the black terminal and positive lead into Diagram 8 the red terminal. Never block the fan grills in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail. Ground Lift Switch – This switch is used to disconnect the internal ground signal from the amplifier ddj ground.
Mono bridge operation connections will follow the above descriptions however, when operating in mono bridge operation the speaker connections will run between the two positive red leads. It’s a community-based project which helps to repair anything.
Be sure that your ameriacn gain controls are turned down to their lowest level full counter-clockwise. During low level output the fans run at normal speeds.
Fuse Holder – 10 5 11 6 12 1 Diagram 3 This holder houses ameerican external fuse. Before using this amplifier, read the user manual for further warnings. To prevent electrical shock or fire hazard, do not expose this amplifier to rain or moisture. Low Dm Frequency Selector – When the Low Cut Filter is activated, dip switches 2 channel americcan and 3 channel 2 will control the frequency roll-off.
The unit also provides a way to rear mount the unit into a rack for added security. When dip switches 2 and 3 are in the “ON” the filter will cut off frequencies at and below 30Hz, when these dip switches are in the “OFF” position the filter will cut off americqn at and below 50Hz. Diagram 6 Diagram 11 When connecting your speakers to the amplifier using spade connector; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps.
This booklet contains important information concerning the proper and safe operation of your new amplifier.
American DJ V 2 Channel Professional Stereo Amplifier | eBay
For cable runs shorter than 20ft. The speaker wire may be connect by bare wire directly connected, usually for permanent connectionsbanana plug, or spade connector. These amplifiers are designed to provide a big impact in sound reproduction. The Output Short Circuit Protection protects the output devices of the amplifier from short circuits and stressful loads.
The front panel provides four holes used to screw the unit into a rack. Ground Lift Switch This switch is used to disconnect the internal ground signal from the amplifier chassis ground. Be sure not to raise the volume to the clip level, however an intermittent clip amerian is acceptable.
Channel 2 Frequency Adjustment. During signal overload, the limiter will reduce the input audio signal enough to minimize the amount of clipping.
Connect an input signal to channel one. Below rated output, 8 ohms dB, unweighted dB, unweighted dB, unweighted dB, unweighted dB, unweighted Power Consumption: Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss of bass response. Cooling Vents – These vents are used for vj cooling.
American Audio V3000/V2000 Stereo Amplifier User Manual
Diagram 10 When connecting your speakers to the amplifier using bare wire; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. Use channel americaj positive output terminal for the negative connection and the channel one positive output terminal for the positive connection.
Refer all servicing to qualified service personnel.