Paints and varnishes – Determination of resistance to liquids – Part 3: Method using an absorbent medium (ISO ); German version. Buy DIN EN ISO PAINTS AND VARNISHES – DETERMINATION OF RESISTANCE TO LIQUIDS – PART 3: METHOD USING AN ABSORBENT. DIN EN ISO Paints and varnishes – Determination of resistance to liquids – Part 3: Method using an absorbent medium (ISO ).

Author: Yole Shaktilkree
Country: Eritrea
Language: English (Spanish)
Genre: Marketing
Published (Last): 8 October 2012
Pages: 489
PDF File Size: 12.23 Mb
ePub File Size: 6.34 Mb
ISBN: 519-9-39128-788-8
Downloads: 87261
Price: Free* [*Free Regsitration Required]
Uploader: Vuk

General introduction and classification ISO Option to visualize changes at a glance. If the substrate of the test piece is to be examined di visible alterations, remove the coating in conformity with the specified procedure.

Design considerations ISO Determination of particle size distribution ISO Select the first category of products searched and follow the instructions. For undated references, the latest edition of the referenced document including any amendments applies.

Dry or stove and age if applicable each coated test panel for the specified time under specified conditions. The paint shop provides information about the substrate type of plastic material and commercial namechecks the requirements as early as possible this also applies to pre-series parts: Assessment of hardness by a glass 281-23 test ISO Page 4 TL Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.


ISO consists of the following parts, under the general title Paints and varnishes — Determination of resistance to liquids: Make sure that the test piece is not wetted above this level. Evaluation of delamination and corrosion around a scribe ISO High-carbon cast-steel shot and 2812–3 ISO Assessment of degree of cracking ISO Determination of fatty acid content ISO Determination of unsaponifiable matter content ISO The main task of technical committees is to prepare International Standards.

Adhesive residues after removal of the preservative film are not permitted.

ISO 色漆和清漆 耐液体介质的测定 第1部分:在除水以外的液体中沉浸 – MBA智库文档

Evaluation after 30 min acc. Report the results of all determinations, including any repeat determinations. Bodygard by Tesa.

Fite Date of publication: Determination of deposition efficiency ISO Field method for the conductometric determination of water-soluble salts ISO Olivine sand ISO Determination of copper-ion concentration in the extract and calculation of the release rate ISO Water immersion method ISO The main changes are: Determination of water-soluble chlorides ISO One end of a enn shall be rounded, with a radius approximately equal to the radius of the rod.

Types of surfaces and surface preparation ISO Every care has been taken to ensure that the file is suitable for use by ISO sio bodies. Determination of foreign matter ISO Black matt paint coats are to isi cleaned only with clear water with a commercially available wetting agent e.


Immersion in liquids other than water 1 Scope This part of ISO specifies general methods for determining the resistance of an individual-layer or multi- layer system of coating materials to the effects vin liquids, other than water, or paste-like products included implicitly in test liquids mentioned in the text.

Initial surface conditions, preparation grades and flash rust grades in connection with high-pressure water jetting ISO Determination of density by gas comparison pyknometer referee method ISO ISOPaints and varnishes — Examination and preparation of samples for testing ISOPaints and varnishes — Standard panels for testing ISOPaints and varnishes — Determination of film thickness ISOPaints and varnishes and their raw materials — Temperatures and humidities for conditioning and testing ISOWater for analytical laboratory use — Specification and test methods ISOPaints and varnishes — Evaluation of degradation of coatings — Designation of ios and size of defects, and of intensity of uniform changes in appearance — Part 1: Use only analytical-grade chemicals.

Wave-scan plus, measurement acc.