Gauging of hexagon sockets (ISO ); German version EN ISO ISO Gauging of hexagon sockets. standard by International Organization for Standardization, 01/15/ View all product details. Buy NF EN ISO Gauging Of Hexagon Sockets from SAI Global.
|Published (Last):||11 June 2006|
|PDF File Size:||18.70 Mb|
|ePub File Size:||15.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.
BS EN ISO 23429:2004
The main task of technical committees is to prepare International Standards. Acceptability Acceptance procedure is covered in ISO In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy.
If, in special cases, specifications other than iiso listed in this International Standard are required, they should be selected from existing International Standards, e. For 234299 references, the latest edition of the referenced document including any amendments applies. For dated references, only the edition cited applies. Endorsement notice The text of ISO ISO shall not be held responsible for identifying any or all such patent rights.
BS EN ISO – Gauging of hexagon sockets
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Julyand conflicting national standards shall be withdrawn at the latest by July In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Hexagon socket button head screw ISO – M12 40 – They shall nevertheless meet the other material and property requirements for the respective property class specified in ISO The work of preparing International Standards is normally carried out through ISO technical committees.
Each member body interested in a subject for which a ixo committee has been established has the right to be represented on that committee. Adobe is a trademark of Adobe Systems Incorporated. Intermediate nominal lengths according to ISO are permissible. NOTE Particular attention is drawn to the note in Table 2 and to Table 3 concerning the limitation on ultimate tensile load.
Every care has been taken to ensure that the file is suitable for use by ISO member bodies. Alternative form of socket permissible For broached sockets which are at the maximum limit of size the overcut resulting from drilling shall not exceed of the length of any flat of the socket which is.
Symbols and designations of dimensions are defined in ISO Requirements for non-electrolytically applied zinc flake coatings are covered in Lso Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
DIN EN ISO – Gauging of hexagon sockets –
In accordance with Adobe’s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
Technical Committee Mechanical fasteners 2429 and printing: All rights reserved; No part of this publication may be reproduced or utilized in any form or by any means — elec- tronic, mechanical, photocopying iwo any other data carriers without prior permission from ON!
Table 3 — Minimum ultimate tensile loads for hexagon socket button head screws of the values specified in ISO Thread Property class 8. This third edition cancels and replaces the second edition ISO International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
In addition, when full-size screws are loaded using the type of testing fixture illustrated in ISOthey shall withstand, without 2429, the minimum ultimate tensile loads given in Table 3.